Car keyless access control system challenges remote access control system

Car keyless access control system challenges remote access control system

Strategy AnalyTIcs Automotive Electronics Service released the latest research report "Automobile Entry / Start System: Passive Systems will challenge Remote Control Access Control System (RKE)". The report points out that the comparison of RKE with PG (Passive Go) system and PEG system (Passive Entry Go) will be dwarfed. With the PG system, the driver needs to open the door with a key, but the car can be started without the key; with the PEG system, the driver can open the door and start the car without pulling the key from the pocket.

Strategy AnalyTIcs forecast:

-By 2016, the installed capacity of PEG system may not exceed 11 million sets. If the cost can be reduced and consumer awareness can be improved, the installed capacity of the PEG system will likely increase to 19 million units, with a market size of 877 million US dollars.

-By 2016, sales of more cost-effective PG systems can reach 26 million units.

Although passive systems provide convenience to drivers, their development costs are very high. The development of passive systems for each vehicle model needs to be tailored, with more components and complicated installation. Moreover, consumers are basically not familiar with keyless operation.

Strategy AnalyTIcs, an automotive electronics service industry analyst and Kevin Mak, author of this report, believes: "Vendors have been committed to developing more integrated solutions to solve cost issues and enhance system reliability, usability, and functionality to make consumption When purchasing passive systems, they feel that they are worth the money. The PG system greatly improves the convenience of the traditional RKE system, and the cost is not as high as the development of a complete PEG system. If successful, by 2016, the manufacturer may realize PG The system and the RKE system have equal emphasis on the market. "

The future key system will also provide additional information, such as vehicle temperature, the long-distance two-way communication terminal advocated by GM and Volvo is the best evidence.

The Solder Cups D-sub connector, also known as Solder Cups  D-sub connector , typically contains a pin layout of 9 pin , 15 pin , 25 pin , 37 pin & 50 pin positions housed in increasing shell sizes accordingly. They are available in both male (plug) and female (socket) variants with the male signal contacts/pins (current rating of 5A) spaced every 2.76mm in horizontal rows and the spacing of rows vertically at 2.84mm laid out half the distance between pins of existing rows.


IP66 IP67 Rated Waterproof D-Sub Panel Mount Solder Connectors
Harsh outdoor or indoor environments can destroy electronic equipment. Standard D-sub connectors are not intended to withstand contaminants such as water and dust. These waterproof solder cup connectors are available in male or female genders and DB9, DB15, DB25, and HD15 sizes. They will accommodate wire ranges from 30 - 20 AWG. Construction features gold plated brass contacts, nickel plated steel shells, and a silicone insulating ring. Maximum recommended panel thickness is 0.078".

Antenk offer a wide range of waterproof Standard Density and high density male and female high density D-Sub connectors solder cup  with stamped and formed Contacts in cable mount used in a variety of demanding applications.


Antenk's Solder Cup D-Sub Connectors Stamped contacts

FEATURES

Solder cup d-subs available in industry sizes/positions

Low cost economy series.

Nickel shells have indents to provide grounding and additional retention.

Low cost & high performance, non-removable stamped contacts.

Optional mounting hardware available.


Antenk's SOLDER CUP D-SUB CONNECTORS Stamped contacts

MATERIALS

Shell: Steel, Tin or Nickel Plated

Insulator: Glass-filled thermoplastic. U.L. rated 94V-O

(230°C process temp)

Stamped contacts: Male pins - Brass | Female pins - Phosphor bronze

Plating: Gold flash on entire contact (contact us for other plating options)



Solder Cup Waterproof D-Sub Connector

Solder Cup Waterproof D-Sub Connector Stamped & Formed Contact, Solder Cup Waterproof D-Sub Connector Machined Contacts, Waterproof Panel Mount Solder Cup D-Sub Connector

ShenZhen Antenk Electronics Co,Ltd , https://www.antenk.com

Posted on